- 1 How can you tell the difference between an 8N and 9N Ford tractor?
- 2 What year is my Ford 8N tractor?
- 3 What year was Ford 9N made?
- 4 How do you read a Ford tractor model number?
- 5 Which is better 8N or 9N?
- 6 How many hours are too many for a tractor?
- 7 How do you tell the year of a tractor serial number?
- 8 How do I know what Ford tractor I have?
- 9 How do you tell what year a tractor is?
- 10 Is a Ford 9N a good tractor?
- 11 How much horsepower does a Ford 9N tractor have?
- 12 Does Ford still make tractors?
- 13 How do you read a tractor serial number?
- 14 How do you read a Massey Ferguson serial number?
- 15 Where is the serial number on a Ford NAA tractor?
How can you tell the difference between an 8N and 9N Ford tractor?
You can also tell between an 8n and 9n Ford tractors by the positioning of the brake pedal. The 9n has the two brake pedals on opposite sides, so you have a brake pedal close to your right foot and another close to your left foot. On the other hand, the 8n has both brake pedals on the right side.
What year is my Ford 8N tractor?
To determine the year of a Ford 8N tractor, the serial number must be located and then compared to a list of serial numbers used by Ford for each of the years in which the tractor was manufactured. Locate the serial number imprinted on the Ford 8N tractor.
What year was Ford 9N made?
When introduced in October 1939, the now-named Ford-Ferguson 9N sold for a mere $585, easily a quarter less than the cost of a competing tractor. Certainly, Ford’s ability to turn out massive quantities of cars or tractors in assembly-line efficiency (a manufacturing process Henry Ford invented) helped contain costs.
How do you read a Ford tractor model number?
The first digit will tell you what year the tractor was built in. Ford tractors have a special system to designate the year of production. The number 5 will refer to the year 1965, the number 6 will refer to the year 1966 and so on.
Which is better 8N or 9N?
They really are basically the same. Only major differences are a couple horsepower, 8n has 4 speed trans and 9n has 3 speed trans. 8n is newer than the 9n and has more hp. Newer 8n have side distributor older 8n’s and 9n’s had front distributor.
How many hours are too many for a tractor?
Registered. I think that diesel engines on large tractors generally are good for 7000 to 10,000 hrs with decent care. Smaller tractors with diesels might be good for a little less, say 5k to 8k (most run at higher RPMs). And gasoline tractors good far about 6k to 8k with appropriate care.
How do you tell the year of a tractor serial number?
Your owner’s manual contains information on how to locate all the identification numbers. The 8th digit of the tractor identification number corresponds to the tractor’s model year. To determine the model year, locate the 8th digit of your identification number and compare it to the appropriate table below.
How do I know what Ford tractor I have?
Serial numbers on the 9N-2N and 8N tractors are located on the left side of the engine block, just below the head and behind the oil filter. The hundred series and “01” series tractor serial number location is on the flat area above and behind the starter. The first number is the model number.
How do you tell what year a tractor is?
To determine this, look at the tractor production code, also known as the unit date code. The first digit of the tractor production code gives the production year. For tractors manufactured between 1965 and 1974, the digit corresponds with the last number in the year.
Is a Ford 9N a good tractor?
The short answer is yes. The 9N is one awful tractor to work compared to an 8N, NAA or later. Not only do you don’t get position control and live hydraulics like on the 8N, both the clutch and left wheel brake are on the left, meaning with the clutch depressed you can only use the right brake.
How much horsepower does a Ford 9N tractor have?
The 9N weighed 2340 pounds and had 13 drawbar horsepower, which could pull a two-bottom plow. It was designed to be safe, quiet and easy to operate.
Does Ford still make tractors?
Ford, which began making farm tractors in 1916, no longer produces any in this country, depending on output from factories in Canada, Belgium and England.
How do you read a tractor serial number?
How to read a tractor serial number list: Tractor serial number lists nearly always show the first tractor built in each year. The other tractors for that year will have successively higher numbers. Your serial number should lie between two of the stated numbers.
How do you read a Massey Ferguson serial number?
VIN number on right hand chassis rail. Top line: digits 1 to 9 from the VIN between 2 inverted triangles. Bottom line: digits 10 to 17 between 2 inverted triangles. Prior January 1st 2016, the serial number plate is located just below the rear inspection window, except for the MF5600, 6600, 7600 & 8600 series tractors.
Where is the serial number on a Ford NAA tractor?
Serial number location on later NAA models was on the left side of the transmission case just below the flat above the starter bulge as shown in the photo below. The Hundred series and newer tractor serial number location is on the flat area above and behind the starter.