Question: How To Choke Start A Craftsman 24 Hp Riding Lawn Tractor?

How do you start a Craftsman riding lawn mower with a choke?

The choke lever lies on the left of the steering wheel. Turning it on will increase the fuel supply to provide a rich mixture to the engine. Now you can start your mower with ease by turning the ignition key clockwise. After starting the riding Craftsman mower, pull the throttle lever towards the rabbit position.

How do you start a choke on a riding lawn mower?

Pull the throttle into the choke position. Move the throttle lever so it engages the choke. Depending on the mower, this is done by positioning the lever between the fast and slow settings or pulling it upwards past fast to a point sometimes indicated by a circle with a diagonal line through it.

How do you start a old Craftsman lawn mower?

Hold the brake and turn the parking brake lever on. To start driving the lawn mower, you will need to disengage the brake. Then take the key and turn it in a clockwise motion to start the riding lawn mower. After the engine has started successfully, you can release the key.

You might be interested:  Often asked: How Do I Convert A Lawn Tractor Into A Racer?

Where is the choke on Craftsman riding lawn mower?

The actual choke is located in the opening of the carburetor. It is a plate that restricts the air flow into the carburetor when the throttle lever is placed in the choke /start position.

How do you start a riding lawn mower that has been sitting for years?

To get the mower started, you may have to change the gas and clean or change the plug.

  1. Check the oil before you start a four-cycle mower that has been sitting for a long time.
  2. Prime the engine by pushing the priming bulb three times.
  3. Give the spark plug wire a little tug to see if it’s loose.

Is it bad to run an engine with the choke on?

Leaving the choke on for too long will cause unnecessary engine wear and waste fuel. This is also bad for the environment. This is done by the carburettor where the fuel is mixed with clean air coming from the air filter, and sent into the pistons to be ignited.

How do you start a riding lawn mower without a key?

Using A Jumper Cable To Start The Mower Using a jumper cable is an effective way to start the lawnmower without keys.

What will cause a riding lawn mower not to start?

There are many reasons a riding lawn mower won’t start —everything from stale gas to ignition switch problems. If you constantly have to charge the battery, a bad battery or failed alternator could be causing the problem. Lawn mower ignition switch problems can prevent the starter from getting current.

You might be interested:  Question: Is There A Video Showing How To Assemble A Snow Blade To A Sears Craftsman Garden Tractor?

Where is the choke on a craftsman lt2000?

Look at the throttle cable linkage/governor bracket on the left rear side of the engine. Follow the throttle cable to where it connects to a slider. Now, find the top of the choke blade shaft on the carb. Even with the air cleaner assembly installed, you should be able to see it.

How do you start a craftsman m210?

Open the gas tank, and make sure it is full. Press the primer button on the front of the engine three times to get fuel into the carburetor so the engine will be ready to start when you pull the cord. Click to see full answer.

How do you start a craftsman platinum lawn mower?

How do you start a craftsman platinum lawn mower?

  1. Check the lawnmower engine oil before starting the engine to prevent damage to the internal rotating engine parts.
  2. Twist the gas cap from the fuel filler tube located on the fuel tank.
  3. Push the rubber primer bulb in on the side of the lawnmower engine carburetor five times by hand to start a cold engine.

Why does my Craftsman mower won’t start?

Your Mower Won’t Start: Other possible causes include: Loose, Dirty or Disconnected Spark Plug in Your Lawn Mower: Check it out, clean off debris, re-connect and tighten. Dirty Air Filter: Clean or replace. Fuel Not Reaching the Engine: Tap the side of the carburetor to help the flow of gas.

How do you turn off a Craftsman lawn mower?

How to Shut Off a Lawn Mower Without a Kill Switch

  1. Stop pushing the lawn mower. Make sure you are standing still and the mower is on level ground.
  2. Pull the throttle to the ” Stop ” position.
  3. Locate the spark plug wire on the lawn mower. It should travel from the throttle to the motor.

Leave a Reply

Your email address will not be published. Required fields are marked *