Often asked: How To Rebuild Injector Pump On A Ford 1210 Tractor?

How do I know if my tractor injector pump is bad?

Symptoms of a Bad or Failing Diesel Injection Pump

1. Engine may run roughly, or not at all.
2. Hard starting.
3. Engine misfires.
4. Lack of power.
5. Excessive smoke from the exhaust.

How long do injector pumps last?

Fuel pumps have been known to last for over 200,000 miles in some cases. After 100,000 miles, the failure of the pump is likely enough that if you are replacing a major part in the fuel system nearby, it may be advantageous to replace it at the same time.

What are the major parts of a ve injection pump?

• Head & Rotor.
• Solenoid Valve.
• Transfer Pump.
• Fuel Filter.
• Throttle Shaft.
• Glow Plugs.
• Governor.
• Flyweight.

How do you time a fuel injection pump?

If you decide to alter the fuel injection pump, you’ll need to:

1. Use a socket wrench on the front camshaft bolt to hand-turn the engine clockwise until the first cylinder is at TDC.
2. Both the intake and exhaust valves should be closed, and the TDC mark should be aligned.

What causes injector pumps to fail?

One of the major reasons for injector pump failure is an excessive buildup of deposits. There are two types of deposits – internal injector deposits and external injector deposits. External injector deposits are caused by fuel that’s not wholly burned that often builds up around the injector holes.

How much does it cost to replace an injector pump?

To get your injector pump replaced, you are looking at anywhere from $1,400 to $1,875. For labor, you should pay between $770 and $1,000, while parts will run between $685 and $900.

What are the symptoms of a bad diesel fuel injector?

Here are the 5 most common symptoms of faulty diesel fuel injectors.

• Trouble starting the vehicle or uneven idling. The engine cranks but doesn’t start unless you crank it for a long time.
• Misfire.
• Smell of fuel.
• Dirty emissions.
• Increased fuel consumption and poor miles per gallon.

How much does it cost to replace diesel injectors?

On average, you can expect to pay between $350 and $850 to replace your fuel injectors.

What is the function of injector pump?

An Injection Pump is the device that pumps fuel into the cylinders of a diesel engine. Traditionally, the injection pump was driven indirectly from the crankshaft by gears, chains or a toothed belt (often the timing belt) that also drives the camshaft.

What is a VE pump?

The VE injection pump is a mechanically controlled, axial-piston rotary pump. It uses a vane-type supply pump to generate an internal pump pressure that increases with engine speed. This plunging and rotating shaft generates injection pressure and controls injection timing.

How do you adjust a VE pump?

The Bosch VE pump can be turned up by turning the power adjustment screw clockwise about 1 to 2 turns. This power adjustment screw is located on the firewall end of the injection pump under a plastic cover that will pop off.

How do I test my injection pump timing?

By removing deflector from fuel pump

1. Take out deflector on both sides of the fuel pump.
2. Put hand torch on one side of pump and mirror on the other side.
3. The light from torch will be visible on the mirror.
4. Turn the engine so that the unit to be check is toward the TDC of compression (at plunger upstroke)

How do you check fuel injector timing?

Hair line Test is a method of checking fuel pump timing by looking for the crank angle when the marking on plunger and its body coincides. When the unit is at TDC with both markings on plunger and its body coincide; the crank angle marking on flywheel will tell the exact position of fuel injection on timing diagram.

How do I adjust my injection timing?

There are several ways you can adjust injection timing, depending on the type of engine you have and how old it is. The most common ways to adjust injection timing are programming the ECM, adjusting the fuel injection pump, replacing the camshaft, and replacing the cam followers or gaskets.