Contents
- 1 How do you engage the blades on a Craftsman riding lawn mower?
- 2 Why won’t my Craftsman mower blades won’t engage?
- 3 Why won’t my riding lawn mower blades engage?
- 4 Why did my mower blades stop working?
- 5 Why won’t my Blades won’t engage?
- 6 Why does my lawn mower stall when I engage the blades?
- 7 Why is my riding mower not cutting?
- 8 Can you put a mulching blade on any mower?
- 9 Do mulching blades go up or down?
- 10 Is mulching better than side discharge?
How do you engage the blades on a Craftsman riding lawn mower?
Find the plunger at the top of the attachment lift lever. Press the plunger inward with your thumb, and move the attachment lift lever back, or toward you, to lower the cutting blade. Release the plunger and attachment lift lever. Pull the attachment clutch switch outward to ” Engage ” to make the cutting blade rotate.
Why won’t my Craftsman mower blades won’t engage?
If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage. The PTO clutch is not repairable—if the clutch is defective, you must replace it. The PTO switch provides power to the PTO clutch.
Why won’t my riding lawn mower blades engage?
Top Reasons why your blades will not engage on your riding mower or tractor: Belt-the number one cause for your blades not to engage is that your belt is either stretched or loose causing it to slip or fall off completely. Belt could have snapped also.
Why did my mower blades stop working?
If your mower blades will not turn after the blade controls have been engaged, your deck belt may be broken. The deck is located directly under the operators seat. This belt spins the mowers blades and runs through a pulley system of idlers. If the belt has snapped, it will need to be replaced.
Why won’t my Blades won’t engage?
If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage. The PTO switch provides power to the PTO clutch. If the switch is defective, it may not supply power to the PTO clutch.
Why does my lawn mower stall when I engage the blades?
If a pulley doesn’t spin freely, it can cause the engine to die when the blades are engaged. The pulleys in your lawn tractor are driven by the drive belt, and turn the spindles. If a pulley doesn’t spin freely, it can cause the engine to die when the blades are engaged.
Why is my riding mower not cutting?
Stepped cutting is usually caused by mower deck damage, mower blade, or misadjustment. Stepped Cutting.
| CAUSE | SOLUTION |
|---|---|
| Deck is not leveled correctly | Level the deck correctly |
| Tires are not properly installed | Check and inflate tires |
| Blades are damaged | Replace the blades |
| Deck shell is damaged | Repair or replace the deck |
2
Can you put a mulching blade on any mower?
Yes, you can put a mulching blade on almost any mower. To put a mulching blade on a mower, the blade needs to be able to fit the deck properly and be secured tightly. Not all mowers equipped with a mulching blade will do a good mulching job due to bad deck design, or low-powered engine.
Do mulching blades go up or down?
Most blades have the word “ bottom ” stamped on them, or they have a model number imprinted onto the underside. Whether a word or a number, that side of the mulching blade must face the ground after it is installed and the mower is standing upright. Part of the blade is bent upward slightly.
Is mulching better than side discharge?
No. Both side – discharge and mulching mowers leave grass blades behind. However, a mulching blade chops up clippings into finer pieces so they decompose faster and don’t clump as quickly. Using a side – discharge mower you may need to do your own mulching by running over your grass piles multiple times.